Standard solar street light-litelsolar manufacturer for mid pole light and high pole light

Pole lights in high pole lights can generally be divided into lift type and non-lift type. The height of the main pole of the lifting type is generally more than 18 meters, and the electric lifting operation is convenient. After the lamp panel is raised to the working position, the panel can be automatically removed, hung in the ditch, and the wire rope can be unloaded. The lift-type high-pole light has two lifting control modes, manual and electric, so that the light panel can be safely and reliably lowered to 2.5 meters above the ground, which is convenient for maintenance work. 1. The poles, lamp panels, wiring, and lifting and lowering motor mechanisms of mid-pole lamps and high-pole lamps should comply with the current industry standard 'Technical Conditions for High-Pole Lighting Facilities' (CJ/T3076-1998). Structure of medium and high pole lighting facilities. 2. Three-phase power supply should be used for mid-pole lights and high-pole lights, and the three-phase load should be evenly distributed, and protection devices must be installed in each circuit. 3. Stakes should be provided for the top elevation of the foundation. 4. The excavation depth and size of the foundation pit shall comply with the design regulations. The allowable deviation of the depth of the foundation pit should be ten 100mm, -50mm. When the deviation between the foundation pit depth and the designed pit depth is more than 100mm due to soil quality reasons, it should be handled according to the following regulations: (1) When the deviation is +100mm and -50mm, stone paving and grouting should be used. (2) When the deviation exceeds +300mm of the specified value, the part exceeding +300mm can be tamped with soil or sand or stone. Then use paving stone grouting treatment. 5. The length of the anchor bolts buried in the concrete should be greater than 20 times its diameter, and should be welded firmly with the main reinforcement. The anchor bolts should be removed from rust, and the threaded part should be protected. The diameter of the center of the flange holes should be the same, and the deviation should be smaller than that of the bolts. Double nuts and spring washers should be used. 6. The formwork for pouring concrete should be made of steel formwork. The surface should be flat and the joints should be tight. The formwork should meet the requirements of the design size of the foundation. Before the concrete is poured, the surface of the formwork should be coated with a release agent. 7. When pouring the foundation, it should comply with the relevant provisions of the current national standard 'Code for Design of Concrete Structures' (GB50010-2002). 8. The backfill of the foundation pit shall meet the following requirements: (1) For soil suitable for compaction, compaction shall be carried out once every 300mm of backfill thickness, and the compaction degree shall reach 80% of the compactness of the original soil. (2) For the water-saturated viscous soil that is not suitable for compaction, it should be filled in layers, and the density of the backfill should reach 80% of the original soil. solar street light,solar street light manufacturer,high pole light,high pole light manufacturer,street light,street light manufacturer,street light,street light manufacturer,led street light,led street light manufacturer,street light pole,street light pole manufacturer,landscape light,landscape light manufacturer , Magnolia lanterns, Magnolia lanterns manufacturers, minority street lights Yangzhou Global Solar Technology Development Co., Ltd. is a manufacturer engaged in the production of outdoor road lighting, the main products are city circuit lights, solar street lights, high pole lights, led street lights, all kinds of special-shaped Landscape lights, magnolia lights, Chinese lights, ethnic minority street lights, etc.
Many of us have heard about solar lights and seen some of these units in operation in solar led flood lights suppliers, solar led flood lights suppliers and solar led flood lights suppliers spaces.
A detailed plan must be developed if we hope to reach your profitability goal. Once we have a certain figure in mind, Guangzhou Litel Technology Co.,Ltd. and our staff need to determine all the steps necessary to reach that goal and act on them.
Another way to maintain the professional yet engaging innovative technology in solar lights is by embedding new skills directly on manufacturing.
Time is one of the biggest challenges cited by manufacturing solar lights.