Introduction to the maintenance and maintenance methods of high pole lighting facilities

High-pole lighting is a large-scale lighting facility, which has the advantages of large illumination range, good lighting effect, and convenient maintenance. The technical conditions of lighting facilities shall be checked and accepted, and the technical data of high-pole lighting facilities shall be collected and kept, the technical files and a complete set of maintenance and repair operating procedures shall be established and improved, and the annual maintenance and maintenance plan shall be formulated. Contents: Anti-rust paint for light poles, light panels and other metal parts, cleaning and lubricating the transmission mechanism, inspection of fasteners and replacement of damaged light source electrical appliances and circuits. Inspection and maintenance personnel shall obey the unified command of the person in charge of the site, and take corresponding safety measures according to the situation. The lifting operation procedures, the routine maintenance and inspection of the lamp panel are briefly described as follows: 1. Standardize the operation procedures and strictly prohibit illegal operations. When the high pole lighting facilities are lifted and lowered, non-staff and lifting operators must stay away from the center of the lamp pole Above 10m, operators shall not use manual and electric operation at the same time, safety fences should be set up around the safe area, on-site staff should wear safety helmets, and unrelated personnel are strictly prohibited from staying on site. Before the lifting operation, check whether the oil of the gearbox is full, whether the electrical part, the transmission device and the braking device are safe and reliable, and use the manual handle to test the operation. During the lifting process, you should pay attention to whether there is any abnormal noise in the gearbox. If there is any noise, you should stop the machine immediately to check, and continue the lifting operation until the fault is eliminated. The lamp panel rises to the top and the automatic hook unloads the wire rope and the gearbox, that is, the lifting operation is completed. When the lamp panel descends, the unloading hook must be disengaged first, and then the lamp panel can be lowered until the distance from the ground specified by the manufacturer. Maintenance personnel should fasten their seat belts when climbing on the lamp panel for maintenance, and there can only be at most two maintenance personnel on the lamp panel. 2. Maintenance and replacement of high-pole lights When overhauling according to the maintenance plan of high-pole lighting facilities, the lamps, light source electrical appliances, cables and other equipment should be thoroughly and carefully inspected. For safety reasons, an electric shock protector can be installed to prevent electric shock if necessary. At the same time, perform routine maintenance on the following problems. 1. During the process of retracting and unwinding the wire rope, on the other hand, check the appearance of the wire rope, and on the other hand, pay attention to whether the wire rope has overlapping, twisted strands, corrosion, broken strands and severe stress. Check whether the sliding parts are flexible and reliable. 2. Replace the damaged light source electrical appliances, cables, etc., and check whether all the fixing bolts are loose, firm, safe and reliable, whether the positioning pins and automatic hooks are flexible and reliable, etc., and those with serious corrosion should be replaced. 3. Motors, gearboxes and other transmission mechanisms fixed at the bottom of the light pole should be closed and covered as much as possible to prevent the insulation from being damaged due to dampness of the coil. Check whether the oil in the gearbox is sufficient, and whether the oil is black or has impurities. The movable motor drive mechanism should be placed in a dry place, and its insulation resistance (not less than 1mΩ) should be tested with a shaker before operation. 4. The AC contactor, thermal relay, travel switch, command controller and other control electrical appliances in the control circuit of the high-pole light should be carefully and carefully inspected before operation. The electrical components found in the problem should be replaced as soon as possible, and it is strictly forbidden to operate with illness. . 5. The grounding protection devices and lightning protection devices of high-pole lighting facilities must be routinely checked before the rainy season every year, and the grounding resistance should be tested. If the grounding resistance value cannot be reached (should be less than 10ω), it should be dealt with in time. 6. All the above maintenance contents must be recorded in a ledger. After the maintenance work is completed, the electrical parts of the high-pole lighting facilities and the lifting transmission mechanism should be fully inspected again. After confirming that they are correct, the lamp panel can be raised and directly hooked and unloaded before leaving the site. [The above content is organized and released by solar street light manufacturers for you]
The average consumer is always looking for ways to save money while finding out solutions, is designed for killing two birds with one stone, providing a perfect solution to solar lights problems.
What are you waiting for? Don't you want to provide perfect support to solar led flood lights suppliers? If yes, so, switch to solar lights right away!
To strengthen and grow our leadership position by providing solar lights across a range of market segments, including solar led flood lights suppliers, and high-performance servers.
solar lights are raising the stakes of social marketing, but they also ease the sales process by providing ways for solar led flood lights suppliers to effectively interact with customers.